How To Brick Up A Window Uk

Download Article

Download Commodity

If your windows aren't bear upon-resistant, you'll probably want to board them up if a big storm or hurricane is most to hit.^[1] Information technology may seem like a pretty daunting task to board up the windows of a firm, peculiarly if yous've never done it before. Fortunately, whether your house has vinyl, brick, or stucco siding, the process of installing plywood over the windows is relatively straightforward. Merely spiral the plywood over the entire window or use clips to install the plywood within the window frame.

1. 1

   Record the vertical and horizontal measurements for the window. Use a record mensurate to decide the superlative and width of the window you plan to lath upwards and write these measurements down. If the window has an extended sill, mensurate vertically from the top of the sill to the tiptop of the window.^[2]

   • When measuring horizontally, measure within the window's exterior trim.

2. 2

   Cutting a piece of plywood that is 8 inches (20 cm) higher and wider than the window. Add 8 inches (20 cm) to the height and width measurements yous took of the window, then use these new measurements to measure and cutting your plywood. Utilize a circular saw to cut the plywood.

   • For example, if your window measures 48 inches (120 cm) tall and 24 inches (61 cm) wide, then your slice of plywood should be 56 inches (140 cm) tall and 32 inches (81 cm) wide.
   • If the window has an extended sill, yous only demand to add 4 inches (10 cm) to the pinnacle before cutting the plywood.
   • If y'all don't have a circular saw, y'all tin can take your plywood to a dwelling house improvement shop to have it cut for yous.

   Advertizing

3. 3

   Attach 2 pieces of plywood together if y'all need a bigger piece. Most pieces of plywood are 4 by 8 anxiety (ane.2 by 2.iv m), and so if your window's dimensions are larger than this, you'll need to utilize ii pieces of plywood attached to each other. Identify 2 plywood pieces next to each other, and so lay a 2 by 4 in (5.i by 10.2 cm) bracing along the seam. Finally, drill 2.25 in (five.7 cm) screws through the bracing and into the plywood to attach them all.^[three]

   • Drill at to the lowest degree 6 screws (2 at the top of the bracing, 2 in the middle, and 2 at the lesser) through the bracing and into the 2 pieces of plywood to brand sure they're securely attached.

4. iv

   Use a stud finder to find the studs in the wall around the window frame. Y'all'll desire to make certain you lot're not attaching the plywood merely to trim around the wall, since this won't be secure. Wait for the studs 4 inches (x cm) out from each side of the window frame.^[4]

   • If yous don't have a stud finder, you may be able to determine where the stud is past looking for nailheads in the siding, since these nails have probably been nailed into the stud.

5. 5

   Drill holes in the corners of the plywood that marshal with the studs. Drill four holes that are each around 2 inches (5.1 cm) in from the edges of the plywood at each corner. Yous may demand to accommodate this measurement to ensure that the holes you drill volition line up with the studs in the wall when you become to screw in the plywood.^[5]

   • Make sure the holes y'all drill are equal in diameter to the screws you lot volition use to attach the plywood to the wall. Use ⁱ⁄_iv  in (0.64 cm) pan-caput or lag screws for the best results.
   • These holes in the plywood are called "pilot holes." They should exist drilled all the way through the plywood.

6. half dozen

   Make boosted holes at 12 in (30 cm) intervals around the plywood. These holes are where yous will spiral the plywood into the wall. Align these holes with the corner holes you already drilled to ensure that these new holes will also line upwards with the studs in the wall.^[6]

   • If the window has a sill that extends out at the bottom, you only need to drill these holes on the top and sides of the plywood.
   • These holes should also be around 2 inches (5.one cm) from the edge of the plywood.
   • Note that the holes in the top and bottom of the plywood will not be screwed into the studs in the wall.

7. 7

   Identify the plywood over the window frame and use a drill to screw information technology in. ^[7] Have someone hold the board while yous drill screws through each of the pilot holes, or vice versa. Use pan-caput or lag screws that will penetrate at least two inches (5.1 cm) into the framing.^[8]

   • These types of screws are best since their flat-bottomed heads won't sink into the plywood and weaken it.
   • Use corrosion-resistant screws if you're boarding up your window in advance of a hurricane or other major storm.

   Ad

1. 1

   Measure the height and width of the window you're boarding upwardly. Decide the peak and width of the window with a tape measure, making sure to write your measurements down. Measure from the top of the window frame interior to the bottom, as well as from side to side. Don't measure beyond the frame itself.^[9]

   • Your plywood piece will exist cutting to fit inside the window frame, and then in that location's no demand to measure beyond it.

2. two

   Cut a slice of plywood to match the window's dimensions. Use a circular saw to cut the plywood to match the height and width of the window frame. You'll be placing the piece of plywood snugly inside the frame, and so the measurements of the plywood should be equally close as possible to the dimensions of the window.

   • For example, if your window frame measures 48 inches (120 cm) tall and 24 inches (61 cm) wide, then your piece of plywood should be 48 inches (120 cm) tall and 24 inches (61 cm) wide also.
   • Take your plywood to a habitation improvement store to accept it cut for you if y'all don't take a round saw.

3. 3

   Use 2 pieces of plywood fastened to each other if the frame is likewise big. #*You'll need to use 2 pieces of plywood attached to each other with a 2 by 4 in (v.1 by x.2 cm) bracing along the seam if your window frame is bigger than 4 past 8 anxiety (i.two past 2.4 m). Place 2 plywood pieces adjacent to each other with a 2 by 4 in (v.one by x.two cm) bracing placed along the seam. Then, drill 2.25 in (five.7 cm) screws through the bracing and into the plywood to attach them all.^[ten]

   • Drill at least 6 screws (2 at the top of the bracing, two in the middle, and 2 at the bottom) through the bracing and into the 2 pieces of plywood to make sure they're deeply fastened to each other.

4. iv

   Use a hammer to attach 4 window clips to the sides of the plywood. Place 2 clips on each side of the plywood, positioned then that the tension legs are facing towards you. Then, gently tap the clips with the hammer to attach them to the plywood. Be sure to place each pair of clips no more than 2 feet (0.61 m) apart from each other.^[eleven]

   • Position the clips so that they're evenly spaced from each other for best results.
   • You may be able to merely push the clips into identify. Even so, using a hammer will ensure that they are every bit securely attached to the plywood as possible.

5. 5

   Identify the plywood over the window frame and button it in to secure it. ^[12] When y'all practise this, make sure the clips are securely gripping the sides of the frame and aren't being pushed out of it. Push the plywood equally far into the frame as it can become.^[13]

   • Strong winds generate lift on the plywood that can cause it to be pulled out of the window frame. If the window clips are securely gripping the sides of the frame, they will keep the plywood in place.^[14]
   • When you lot're ready to remove the plywood, simply push down on the board and pull up on the window clips on i side to remove information technology.

   Ad

Add New Question

• Question

  How do you cover windows with woods?

  

  Steve Linton is the President of Deltec Homes, a custom home building company in Asheville, Northward Carolina. With nearly 20 years of feel, he oversees all home building projects for Deltec Homes. He specializes in hurricane-resistant homes, green home design, and sustainable building. Steve holds a BS in Structural Engineering from Cornell Academy and is a LEED Accredited Professional person.

  

  Custom Domicile Architect

  Expert Respond

• Question

  How exercise you protect windows without plywood?

  

  Steve Linton is the President of Deltec Homes, a custom domicile building company in Asheville, N Carolina. With nearly 20 years of experience, he oversees all habitation building projects for Deltec Homes. He specializes in hurricane-resistant homes, green home design, and sustainable edifice. Steve holds a BS in Structural Technology from Cornell University and is a LEED Accredited Professional.

  

  Custom Home Builder

  Good Answer

Enquire a Question

200 characters left

Include your electronic mail address to get a bulletin when this question is answered.

Submit

Advertisement

Things You'll Need

• Plywood
• Tape measure
• Stud finder
• Circular saw
• ¹⁄₄  in (0.64 cm) pan-head or lag screws
• Ability drill

• Hammer
• Window clips

• If you have to lath up your windows from the inside (e.one thousand., if the storm is already raging outside), place security window film over the drinking glass and tape it down. This isn't the all-time way to protect your windows and home, but it will work in a pinch.

Advertizing

• If y'all're worried that you lot won't exist able to deeply install the plywood over your windows earlier a big storm hits, hire a professional to do it for y'all. Although this is more expensive, you'll want your house to exist adequately protected for the storm.

Advertising

About This Article

Commodity Summary Ten

To lath upwardly a window, try using plywood. Commencement, measure the height and width of the window so you know how much forest you'll need. And then, cut a piece of plywood and so information technology's viii inches college and wider than the window. If your window is larger than the piece of plywood, attach ii pieces together by screwing a 2 by 4 along the seam betwixt the ii pieces of wood. Side by side, drill holes almost 2 inches from the corner of the plywood, which should line upwardly with the studs in the wall when you screw it in identify. Drill additional holes at 12 inch intervals around the board. Finish by placing the lath over the window and screwing information technology into place. For tips on how to adhere a lath to brick using window clips, read on!

Did this summary help yous?

Thanks to all authors for creating a folio that has been read 36,492 times.

Did this commodity aid y'all?

Source: https://www.wikihow.com/Board-Up-a-Window

Posted by: makrisformaded.blogspot.com

Share this post